Rubber Expansion Joints

OVERVIEW:  When using Flexicraft rubber expansion joints, you can be assured they were designed and built to last.  No one can offer greater security or variety in meeting your needs. Review the rubber elastomer expansion joint models below to choose the optimal design for your application, or contact our highly trained staff for assistance.

ULTRASPOOL SINGLE EXPANSION JOINT

The Ultraspool premium expansion joints are the most versatile rubber spool expansion joint available. They come in diameters from 1" to 120", and can be made with any elastomer material or any other special requirements.

FLEXTRA 150 EXPANSION JOINT

The Flextra 150 spool expansion joints are an excellent value alternative. They are molded and have a wide arch for good movements, and iron retaining rings. Available in butyl and EPDM. From 2" to 24" diameters.

FLEXTRA TS EXPANSION JOINT

The Flextra TS is specially designed for FRP and thermoplastic piping. Low spring rates and built in control rods are easy on the pipe and flanges. 

ULTRASPHERE TWIN EXPANSION JOINT

The Ultrasphere Twin is a variation of the Ultrasphere that allows more movement. 1" to 24" diameters.

FLANGED RUBBER PIPE CONNECTOR

Rubber Pipe Connector is used primarily to suppress noise and vibration from pumps, chillers and other equipment. It does not use an arch, so the movement is limited. Standards from 1-1/2" to 20" diameters, but specials are common.

SLV FLEXIBLE COUPLING

Flexicraft SLV Flexible Couplings is a high quality expansion joint with unique sleeve ends to clamp over pipes. Construction is of reinforced neoprene or silicone, and they are rated for 75psi. 2" through 12" diameters.

ULTRASPOOL DOUBLE EXPANSION JOINT

The Ultraspool Double expansion joints are the standard two arch version of our Ultraspool, which allows additional movement. They come in diameters from 1" to 120", and can be made with any elastomer material or any other special requirements.

1000T SPOOL EXPANSION JOINT

The 1000T Spool expansion joint is a molded arched rubber spool expansion joint for moderate pressures and movements. Available in butyl and EPDM. From 1" to 14" diameters.

ULTRASPHERE EXPANSION JOINT

The Ultrasphere is an economical rubber expansion joint, often connected to pumps and equipment to provide for movement and absorb vibration. The freely rotating metal flanges and tapped holes allow for easy installation. Multiple materials are kept in stock. 1" to 30" diameters.

CONCENTRIC REDUCER EXPANSION JOINT

The Rubber Reducers are spool expansion joints connect unequal size pipes. Standard designs in any elastomer are available from 2" to 18".

FAN CONNECTOR DUCT EXPANSION JOINTS

Fully molded rubber duct expansion joints used as flexible fan connectors with integral rubber flanges are available in round and rectangular configurations for low pressure air & gas services. Any dimensions and flange drill pattern can be fabricated.

DWV FLEXIBLE COUPLING

These economical expansion joints for low pressure drain, waste, and vent applications slip over pipe and accommodate expansion. 1-1/2" to 4" diameters. Purchased in cases of 20 pieces.

ULTRASPOOL TRIPLE EXPANSION JOINT

The Ultraspool Triple expansion joints are the standard three arch version of our Ultraspool, which allows maximum movement. They come in diameters from 1" to 120", and can be made with any elastomer material or any other special requirements.

TEFSPOOL PTFE LINED EXPANSION JOINT

The Tefspool expansion joint is a rubber spool with an integral PTFE liner, giving it the strength and pressure rating of a rubber expansion joint, and the chemical resistance of PTFE. 1.5" to 24" diameters.

ULTRASPHERE W/ CABLES

The Ultrasphere with Cables is a variation of the Ultrasphere with built-in control cables. This eliminates the need for separate control units that must be installed in the field, adding security. 2" to 12" diameters.

ECCENTRIC REDUCER EXPANSION JOINT

The Rubber Reducers are spool expansion joints connect unequal size pipes. Standard designs in any elastomer are available from 2" to 18".

CONTROL UNITS

Control units are required with rubber expansion joints when the piping system is not anchored to properly restrain the joint from expanding under pressure.

MOLDED RUBBER BOOTS

Fully Molded Rubber Boot Coverings are available in any design. Various elastomers can be used for special OEM applications requiring low pressure retaining flexible coverings.

VISIT

617 Jeffers Circle

Exton, PA 19341

CONTACT US

(610) 903.0900

© 2019 |  JH Process